原文：
阀门采购时只明确规格、类别、工压就满足采购要求的传统做法，在当前市场经济环境里是不完善的。因为阀门制造厂家为了产品的竞争，形成了各自的企业标准及产品个性。因此阀门采购员在采购阀门时较详尽的提出技术要求，与阀门制造厂家协调取得共识，作为阀门采购合同的附件是十分必要的。 1.采购阀门的通用要求1.1阀门规格及类别， 应符合管道设计文件的要求。1.2阀门的型号应注明编号。若是企业标准，应注明型号的相关说明。1.3阀门工作压力，要求≥管道的工作压力，在不影响价格的前提下，阀门可承受的工压应大于管道实际的工作压力；阀门关闭状况下的任何一侧应能承受1.1倍阀门工作压力值而不渗漏；阀门开启状况下，阀体应能承受二倍阀门工作压力的要求。1.4阀门制造标准编号应标明，若是企业标准，采购合同上应附企业文件。 2.阀门材质2.1阀体材质，并注明阀体材质牌号及实际的物理化学检测数据。2.2阀杆材质，力求不锈钢阀杆(2CR13)，大口径阀门也应是不锈钢嵌包的阀杆。2.3螺母材质，采用铸铝黄铜或铸铝青铜，且硬度与强度均大于阀杆。2.4阀杆衬套材质，其硬度与强度均应不大于阀杆，且在水浸泡状况下与阀杆、阀体不形成电化学腐蚀。2.5密封面的材质①阀门类别不一，密封方式及材质要求不一；②普通楔式闸阀，铜环的材质、固定方式、研磨方式均应说明；③软密封闸阀，阀板衬胶材料的物理化学及卫生检测数据；④蝶阀应标明阀体上密封面材质及蝶板上密封面材质；它们的物理化学检测数据，特别是橡胶的卫生要求、抗老化性能、耐磨性能；通常采用丁晴橡胶及三元乙丙橡胶等，严禁掺用再生胶。2.6阀轴填料①由于管网中的阀门，通常是启闭不频繁的，要求填料在数年内不活动，填料亦不老化，长期保持密封效果；②阀轴填料亦应在承受频繁启闭时，密封效果的良好性；③鉴于上述要求，阀轴填料力求终身不换或十多年不更换；④填料若需更换，阀门设计应考虑能有水压的状况下更换的措施。 3.变速传动箱3.1箱体材质及内外防腐要求与阀体原则一致。3.2箱体应有密封措施，箱体组装后能承受3米水柱状况的浸泡。3.3箱体上的启闭限位装置，其调节螺帽应在箱体内或设在箱外，但需专用工具才可作业。3.4传动结构设计合理，启闭时只能带动阀轴旋转，不使其上下窜动，传动部件咬合适度，不产生带负荷启闭时分离打滑。3.5变速传动箱体与阀轴密封处不可连接成无泄漏的整体，否则应有可靠的防串漏措施。3.6箱体内无杂物，齿轮咬合部位应有润滑脂保护。 4.阀门的执行机构4.1阀门操作时的启闭方向，一律应顺时针关闭。4.2由于管网中的阀门，经常是人工启闭，启闭转数不宜过多，就是大口径阀门亦应在200-600转内。4.3为了便于一个人的启闭操作，在管道工压状况下，{zd0}启闭力矩宜为240N-m。4.4阀门启闭操作端应为方榫，且尺寸标准化，并面向地面，以便人们从地面上可直接操作。带轮盘的阀门不适用于地下管网。4.5阀门启闭程度的显示盘①阀门启闭程度的刻度线，应铸造在变速箱盖上或转换方向后的显示盘的外壳上，一律面向地面，刻度线刷上荧光粉，以示醒目；②指示盘针的材质在管理较好的情况下可用不锈钢板，否则为刷漆的钢板，切勿使用铝皮制作；③指示盘针醒目，固定牢靠，一旦启闭调节准确后，应以铆钉锁定。4.6若阀门埋设较深，操作机构及显示盘离地面距离≥1.5m时，应设有加长杆设施，且固定稳牢，以便人们从地面上观察及操作。也就是说，管网中的阀门启闭操作，不宜下井作业。 5.阀门的性能检验测试5.1阀门某一规格批量制造时，应委托xx性机构或第三方检验机构进行以下性能的检测：①阀门在工压状况下的启闭力矩；②在工压状况下，能保证阀门关闭严密的连续启闭次数；③阀门在管道输水状况下的流阻系数的检测。5.2阀门在出厂前应进行以下的检测：①阀门在开启状况下，阀体应承受阀门工压值二倍的内压检测；②阀门的关闭状况下，两侧分别承受1.1倍阀门工压值，无渗漏；但金属密封的蝶阀，渗漏值亦不大于相关要求。 6.阀门的防腐处理6.1阀体(包括变速传动箱体)内外，首先应抛丸清砂除锈，力求静电喷涂粉状xx环氧树脂，厚度达0.3mm以上。特大型阀门静电喷涂xx环氧树脂有困难时，亦应刷涂、喷涂相似的xx环氧漆。6.2阀体内部以及阀板各个部位要求全面防腐，一方面浸泡在水中不会锈蚀，在两种金属之间不产生电化学腐蚀；二方面表面光滑使过水阻力减少。6.3阀体内防腐的环氧树脂或油漆的卫生要求，应有相应xx机关的检测报告。化学物理性能亦应符合相关要求。 7.阀门包装运输7.1阀门两侧应设阀门封盖或轻质堵板固封。7.2中、小口径阀门应以草绳捆扎，并以集装箱方式运输为宜。7.3大口径阀门亦有简易木条框架固体包装，以免运输过程中碰损。 8.阀门的说明书和出厂证明阀门是设备，在阀门的说明书和出厂证明中应标明以下相关数据：阀门规格；型号；工作压力；制造标准；阀体材质；阀杆材质；密封材质；阀轴填料材质；阀杆轴套材质；内外防腐材质；操作启动方向；转数；工压状况下启闭力矩；制造厂厂名；出厂日期；出厂编号；重量；连接法兰盘的孔径、孔数、中心孔距；以图示方式标明整体长、宽、高的控制尺寸；阀门流阻系数；有效启闭次数；阀门出厂检测的相关数据及安装、维护的注意事项等。

“ Technical requirements for procurement of valve specifications ”是由提供的国际阀门新闻，译文仅供参考。另外，中国针型阀网还提供相关产品搜索： 、 、 、 、 、 、 、 等。

译文：
Clear only when the valve procurement specifications, type, working pressure to meet the procurement requirements of traditional practices, in the current environment of market economy is incomplete. Because the valve manufacturer for the product competition, formed their own company standards and product personality. Therefore, when the valve valve buyer purchasing a more detailed proposal of the technical requirements, coordinate with the valve manufacturer to reach a consensus, as the valve procurement annex to the contract is necessary. 1. Procurement 1.1 General requirements for the valve size and type of valves, piping design documents should be consistent with the requirements. 1.2 should indicate the number of valve models. If the enterprise standards, identifying types of instructions. 1.3 valve job pressure ≥ pipeline working pressure, without affecting the price of the premise, the valve can withstand the working pressure should be greater than the actual working pressure pipeline; valve closing conditions of any side should be able to withstand 1.1 times the value of working pressure valve without leakage; valve open position, the valve should be able to withstand twice the working pressure valve requirements. 1.4 Valve Manufacturing standard number should be marked, if the enterprise standards, procurement contracts should be attached to business documents. 2. Valve Body Material Material 2.1, and indicate body material grades and actual physical and chemical test data. 2.2 stem material, and strive to stainless steel stem (2CR13), large diameter valves also should be embedded in the package of stainless steel valve stem. 2.3 nut material, brass or cast aluminum with cast aluminum bronze, and the hardness and strength are greater than the valve stem. 2.4 stem bushing material, its hardness and strength shall be not greater than the stem, and is immersed in water situation and valve body is not the formation of electrochemical corrosion. 2.5 ① valve sealing surface of the material different categories, different sealing methods and materials requirements; ② ordinary wedge gate valve, copper ring materials, fixation methods, polishing should note; ③ soft sealing gate valve, valve plate lining plastic materials, physical chemistry and health testing data; ④ valve sealing surface should be marked on the body sealing surface materials and butterfly board material; their physical and chemical test data, especially rubber, health requirements, aging resistance, wear resistance ; usually NBR and EPDM rubber, mixed with recycled rubber is strictly prohibited. 2.6 ① As the valve shaft packing in pipe valves, usually do not open and close frequently, requiring the filling in a few years of inactivity, not aging filler, a long-term effects remain sealed; ② fill valve shaft should also bear the frequent opening and closing When a good seal of; ③ light of the above requirements, fill valve shaft does not seek to change or 10 years of life do not change; ④ Packing For replacement, the valve should be designed to have water pressure conditions change measures. 3. 3.1 speed gear box and outside box materials and corrosion requirements be consistent with the body. Should be sealed box measures 3.2, cabinet assembly can withstand the 3 m water column after the state of immersion. 3.3 box on the opening and closing stopper, and the adjustment nut should be in cabinets or located in the outside box, but special tools need to be working. 3.4 Drive structural design is reasonable, open and close valves can only drive shaft rotation, so as not to traverse up and down, bite moderate transmission parts, does not produce open and close with a load when the separation skid. 3.5 Transmission and valve box office is not connected shaft seal leak as a whole, or string should be a reliable leakage prevention measures. 3.6 cabinets without debris, grease should be protection gear Biting. 4. Valve actuator valve operation of opening and closing 4.1 direction, all should be clockwise closing. 4.2 As the pipe network of valves, often manually opening and closing, opening and closing rotation should not be too much, that is, large-diameter valves should be transferred within the 200-600. 4.3 In order to facilitate opening and closing operation of a person, in the plumbing pressure conditions, the maximum torque should open and close to 240N-m. 4.4 Valves open and close operation should end mortise and tenon, and the size standard, and for the ground so that people can be directly manipulated from the ground. With a wheel valve does not apply to underground pipe network. 4.5 degree valve opening and closing valves open and close the display plate ① degree of scale line should be cast in the gearbox cover or change the direction of the display after the disc casing, all for the ground wire brush on the phosphor scale to show striking; ② direct needle plate material in the case of better management of available stainless steel, or steel plate for the painting, do not make use of aluminum skin; ③ direct drive needle eye-catching, stable fixation, accurate adjustment when opening and closing after Rivets should be locked. 4.6 If the valve buried deeper, the operating mechanism and the display plate distance ≥ 1.5m above the ground when the pole should have added facilities, and fixed-rate stability in order to observe the people and operations from the ground. That is, opening and closing valves in pipe network operation, should not go down operations. 5. Valve Performance Testing of a standard volume of 5.1 valve manufacture, should be entrusted to an authoritative body or third party inspection agency to conduct the following performance test: ① pressure valve in the working conditions of the opening and closing torque; ② in the work pressure conditions, can ensure the continuous opening and closing the valve tightly closed times; ③ valve in the pipe flow resistance coefficient under conditions of detection. 5.2 The valves in the factory inspection should be conducted the following: ① the valve in the open position, the valve should withstand twice the value of the valve working pressure of the internal pressure test; ② valve closed conditions, both sides suffer 1.1 times, respectively valve working pressure values, no leakage; but the metal sealing butterfly valve, leakage is no greater than the value of the relevant requirements. 6. Valve body embalmed 6.1 (including the variable speed transmission box) inside and outside, at first, blasting sand blasting, seek non-toxic powder electrostatic spraying epoxy resin, thickness of 0.3mm or more. Large electrostatic spraying non-toxic epoxy resin valve difficulty should brush, spray similar to non-toxic epoxy paint. 6.2 The internal and the valve plate body to all parts of a comprehensive anti-corrosion requirements, on the one hand immersed in water will not rust, does not arise between the two metal electrochemical corrosion; two aspects of smooth surface to reduce drag through the water. 6.3 The valve body paint anti-corrosion epoxy resin or health requirements, should the appropriate authority of the organs of test reports. Chemical physical properties should meet the relevant requirements. 7. Valve valve packing and shipping 7.1 should be set on both sides of the valve cover or light blocking plate solid seal. 7.2, the small-caliber valve should be tied to rope, and transported to suitable container. 7.3 Summary of large diameter valves are also the framework of solid wood packaging to prevent damage during transport collision. 8. Valve is the instructions and certificate of valve equipment, manual and certificate of the valve should be marked with the following data: valve size; model; pressure; manufacturing standards; body material; stem material; seal material; valve shaft packing material; stem sleeve material; internal and external anti-corrosion material; operation start direction; rpm; work under pressure situation of open and close torque; manufacturing plant name; factory date; serial number; weight; connection flange pore size, pore number, the center hole is; with graphic images indicate the overall length, width and height of the control size; valve flow resistance coefficient; effective opening and closing times; valve factory testing data and installation, maintenance considerations, etc. .