操作与注意事项

1.操作前的准备：

1) 检查布伦六角轴夹头是否处于夹紧的状态。

2) 检查电气限位开关是否处于复位状态。

2.运行操作：

本机的操作模式设有自动操作模式和手动操作模式两种。操作时先起动主电机，然后将被抛光件夹紧在夹具上，并推进工作台导轨板内。

此时，若选择自动操作模式，则机械自动进行合轴操作（由夹具压迫微动开关所致），与此同时，工作台将同步展开纵向进退、横向摆动及抛磨计时工作。当计时终止时（即一个抛磨周期结束）。布伦自动张开，工作台退出后停止运动。随即准备下一批工件进入。

另外，也可选择手动操作模式，按下合轴按钮进行手动合轴操作。

3.额外装置：

为了满足工件局部增光或者修整的需要，本机设有（停止前进）按钮，可停止工作台运作。考虑到安全问题，本机还增设了（紧急停止）手杆，可迅速切断电源。

4.注意事项：

1) 操作时，确保工作夹紧在夹具上方可进入工作台。

2) 打蜡时，用右手拿蜡，左手放在（紧急停止）手杆上，身体站稳，蜡在布伦上平稳、快速移动。

3) 鉴于机械的工作性质，应特别注意日常清洁保养工作，各运转部位如轴承、导轨面、丝杆螺母等应定期加油以保证其充分润滑。

4) 实行培训上岗，安排专人专机负责，避免人身及设备事故的发生。

备注：

     本机在出厂前经过严格的调试，发至用户一般不需要再重新调试，考虑到运输过程中可能导致的情况，请客户在接受设备后再作一次全面的检查，如发现机械出现异常，请及时与我公司联系，请勿自行装拆，如无异常情况即可配电投入生产。

有需要请联系我们哦！在我们公司购机传授您20年抛光工艺哦。

Operations and precautions

1. Preparation before operation:

1) check whether the buren hexagon holder is in clamping state.

2) check whether the electrical limit switch is in reset condition.

2. Operation operation:

The operation mode of the machine is equipped with automatic operation mode and manual operation mode.

When operating, start the main motor first, then the polished parts are clamped on the jig and pushed into the guide board of the workbench.

At this point, if select automatic operation mode, machinery automatic centring operation (caused by the clamp pressure micro switch), at the same time, the workbench will sync up vertically in a horizontal oscillation and grinding time work.

When the timing is terminated (that is, a grinding cycle ends).

Bern opens automatically, and the table stops moving after exiting.

Then prepare the next batch of work-pieces to enter.

In addition, manual operation mode can be selected and manually operated by pressing the button.

3. Additional equipment:

In order to meet the need of local lighting or trimming of work-piece, the machine is equipped with (stop forward) button to stop the workbench operation.

Considering the safety problem, the machine also added (emergency stop) hand lever, which can cut off the power quickly.

4. Precautions:

1) when operating, ensure that the work clamps are clamped on top of the fixture to enter the workbench.

2) when waxing, use your right hand to get the wax, put your left hand on the hand lever, and hold your body. The wax is smooth and moving fast on the Bunuel.

3) in view of the nature of mechanical work, special attention should be paid to the daily cleaning and maintenance work, which should be lubricated periodically to ensure its full lubrication, such as bearing, guide rail, screw nut and so on.

4) the training is on the job, the special person is responsible for the special machine, avoiding the accident of personal and equipment.

Remark:

Debugging the machine carefully before they go out, to users generally do not need to debug again, considering the transport process may lead to the situation, please customers in the receiving equipment and then make a comprehensive inspection, such as mechanical abnormal found, please contact our company, please put down, if no anomalies distribution in production.

有需要请联系我们哦！在我们公司购机传授您20年抛光工艺哦。