原文：
1.检查真空泵管路及结合处有无松动现象。用手转动真空泵，试看真空泵是否灵活。 2.向轴承体内加入轴承润滑机油，观察油位应在油标的中心线处，润滑油应及时更换或补充。 3.拧下真空泵泵体的 引水螺塞，灌注引水或引浆。 4.关好出水管路的闸阀和出口压力表及进口真空表。 5.点动电机，试看 电机转向是否正确。 6.开动电机，当真空泵正常运转后，打开出口压力表和进口真空泵，视其显示出适当压力后，逐渐打开闸阀，同时检查电机负荷情况。 7.尽量控制真空泵的流量和扬程 在标牌上注明的范围内，以保证真空泵在{zg}效率点运转，才能获得{zd0}的节能效果。 8.真空泵在运行过程中，轴承温度不能超过环境温度35℃，{zg}温度不得超过80℃。 9.如发现真空泵有异常声音 应立即停车检查原因。 10.真空泵要停止使用时，先关闭闸阀、压力表，然后停止电机。 11.真空泵在工作{dy}个月内，经100小时更换润滑油，以后每个500小时，换油一次。 12.经常调整填料压盖， 保证填料室内的滴漏情况正常以成滴漏出为宜.。 13.定期检查轴套的磨损情况，磨损较大后应及时更换。 14.真空泵在寒冬季节使用时，停车后，需将泵体下部放水螺塞拧开将介质放净。防止冻裂。 15.真空泵长期停用，需将泵全部拆开，擦干水分，将转动部位及结合处涂以油脂装好，妥善保管。

“ Vacuum pump 15 on the details of maintenance ”是由提供的国际水泵新闻，译文仅供参考。另外，中国化工泵网还提供相关产品搜索：、、、、等。

译文：
1. Check for any possible combination of vacuum tubes and loosening. Rotate the vacuum pump, vacuum pump is flexible Look. 2. To join the bearing lubrication oil bearing body to observe the oil level should be the subject of the center line of the oil, lubricating oil should be replaced or supplemented. 3. Unscrew the plug screw vacuum pump of the water, filling water or introduce slurry. 4. Turn off the valve outlet pipe Road, import and export pressure gauges and vacuum table. 5. To move the motor, and proved correct shift motor. 6. Starting motor, when the vacuum pumps operate normally, open the import export pressure gauges and vacuum pumps, depending on the show after the appropriate pressure to gradually open the valve, and check the electrical loads. 7. Try to control the flow of vacuum pump and the lift on the plate indicate the extent to ensure maximum efficiency point in the operation of vacuum pump in order to maximize energy savings. 8. Vacuum pump during operation, the bearing temperature must not exceed the ambient temperature 35 ℃, the maximum temperature not exceeding 80 ℃. 9. If found to have abnormal noise vacuum pump should be immediately stopped and check the reason. 10. Vacuum pump to stop use, turn off valve, pressure gauge, and then stop the motor. 11. Vacuum pump in the first month of work, replacement of oil by 100 hours, after every 500 hours, oil change time. 12. Constantly adjusting packing gland, packing the room to ensure the normal order into the drip drip out of the situation is appropriate.. 13. Regularly check the wear sleeve, wear in time after a larger replacement. 14. Vacuum pump used in the winter season, parking, the need to unscrew the pump will lower medium Drainage Plug up the net. To prevent the cracking. 15. Vacuum pump long-term disabled, need to pump all apart, dry water, the moving parts and coated with grease loaded binding sites is good, good care.