原文：
If a line-to-lube hole has been drilled in the PR valve circuit, it should be plugged to reduce converter drainback. Inspect the TV checkball separator plate seat. Leakage here may produce stacked shifts and/or no kickdown. Remove the detent assembly & spring retainer bracket, see Figure 1. Remove the original pressure regulator spring and valve. Remove the end plate on the opposite side of the bore and remove the Keep the OEM Align valve body in fixture according to VB-FIX instructions with the appropriate guide pin provided in tool kit F-22771A-TL7. To align the pressure regulator valve use jig F-22771A-RJ and guide pin F-22771A-GP, then ream with reamer F-22771A-RM. Generously lubricate the bore and reamer with cutting fluid (i.e. Mobilmet S-122, Lubegard Bio-Tap, Tap Magic?, etc). For best results, provide a continuous flow of water-soluble cutting fluid (i.e. Mobilmet S-122) during the reaming process. The reamers should be turned using a low rpm, high torque air drill regulated to a maximum of 200 rpm. Examine the bore after cleaning for surface finish, debris, and burrs. Flashing and burrs on the exit side of lands and bores must be carefully removed. A small piece of Scotchbrite? material attached to a wire and powered with a drill motor is ideal for the task. Turning the reamer backward will dull it prematurely. Pushing on the reamer will result in poor surface finish and inadequate and sporadic material removal. Never use a crescent wrench, ratchet or pliers to turn the reamer.
原文来自： http://www.carspdf.com/chrysler-48re-oversized-lube-regulated-pr-valve-linetv-pressure-plug-kit/

Chrysler 48RE Oversized Lube Regulated PR Valve & Line/TV Pressure Plug Kit;是由 提供的阀门新闻，中文译文仅供参考(上海日美阀门制造有限公司还生产 及美标蝶阀，弹性座封闸阀，消防专用闸阀，手柄操作通风蝶阀，液控止回阀，欢迎您的选购。)
以下是参考译文：

译文：压力调节阀弹簧
检查电视checkball隔板席位。这里可能产生渗漏堆叠变化和/或没有kickdown。 删除制动组装及弹簧座支架， 删除原来的压力调节阀弹簧。 xx对对方的孔端板和删除行/ TVpressure插头和套筒大会和春天。 对齐夹具阀体根据VB的修复适当引导针工具包的F - 22771A - TL7提供的说明。为了调整压力调节阀采用跳汰机的F - 22771A - RJ和导柱架F - 22771A -大奖赛，然后用铰刀的F - 22771A -室铰。为了对齐油门压力插头孔夹具使用的F - 22771A - RJ2和导柱架F - 22771A - GP2的，然后用铰刀的F - 22771A - 2令吉铰。至于落后的铰刀过早将沉闷。对铰刀推进会导致较差的表面光洁度和不足，零星材料去除。万不要使用月牙扳手，棘轮或钳子扭转铰刀。 呆滞刀将削减一个较小的黑洞。铰刀，可以激化，但只能由一个专业工具刀完成。现实生活中的铰刀重磨或更换前平均50-70孔。

更多新闻