WD615系列柴 | ||||
序号 | 名 称 | 产品序号 | 单位 | 用 途 |
1 | 正时中间齿轮与机油泵中间齿轮与喷油器拨出器 Extractor puller for timing intermediate gear shaft liner and oil pump intermediate gear shaft liner and fuel injector | TZ-FD01 | 套 | 用于更换正时中间齿轮和机油泵中间齿轮及拨出喷油器 It will need the special extractor puller for pulling out the timing intermediate gear shaft liner and oil pump intermediate gear shaft liner when disassemble the engine timing gear mechanism. Additionally, the fuel injector of Euro II engine must be pulled out from the cylinder head by this special extractor puller. |
2 | 缸套拨出器 Cylinder liner puller | TZ-FD02 | 套 | 用于更换缸套时,从缸体中拨出旧缸套 The cylinder liner puller is used to pull out the worn liner from cylinder bore. |
3 | 气门拆卸工具 Valve disassemble special tool | TZ-FD03 | 套 | 用于拆卸气门锁片 Valve is fixed on the valve spring seat by a lock after the valve is assembled on the cylinder head, so it is necessary to use special tool to disassemble valve |
4 | 气门导管冲棒 Valve guide bar | TZ-FD04 | 只 | 用于安装新气门导管 It is need A=22mm from the valve guide to valve spring seat |
5 | 喷油器衬套拆装工具 Tool to dissemble the fuel injector liner | TZ-FD05 | 套 | 用于更换喷油器铜套时,拆装旧衬套和安装新衬套 we should change the eroded liner by a new one. This is the fuel injector disassemble tool |
6 | 气缸压力表 Cylinder pressure gauge | TZ-FD06 | 套 | 用于测量气缸压力(欧I、欧2) Check cylinder pressure one by one by this gauge.for Euro I & II |
7 | 气门座铰刀(欧I) Reamer for valve seat | TZ-FD07II | 套 | 用于修复铰削进、排气门座口(配套) The working taper of WD615 series engine exhaust valve normally is 90º, and air intake valve working taper is 110ºbut not standard angle. So it is necessary to use the special reamer |
8 | 气门座铰刀(欧II) Reamer for valve seat | TZ-FD08 | 只 | 用于修复铰削进、排气门座口(配套) The working taper of WD615 series engine exhaust valve normally is 90º, and air intake valve working taper is 110ºbut not standard angle. So it is necessary to use the special reamer |
9 | 气门导管铰刀 Reamer for valve guide | TZ-FD09 | 套 | 用于铰削气门导管(直径11毫米和直径12毫米) During maintenance to replace the valve guide, ream the guide inner hole when the new guide is pressed into cylinder head |
10 | 喷油泵调试拆装专用工具 Fuel injection pump disassemble tool | TZ-FD10 | 只 | 用于拆装和调试波许喷油泵及调速器 This tool is designed to disassemble and check the injection pump and speed governor when replace parts on testing bench. This tool is fit for imported and local produced Bosch P type pump. |
11 | 60~300N/M可调式扭力扳手 Adjustable torque wrench 60~300N·M | TZ--GJ01 | 台 | 用于扭紧发动机全部有扭距要求的螺栓 To maintain the engine, there will be stipulated torque to fasten the key bolt. The torque of 60~300N·M is fit for all the bolts which have torque requirement of WD615 series engine. |