齿轮泵常见故障及排除方法

齿轮泵常见故障及排除方法

2010-06-02 17:02:33 阅读15 评论0 字号:

原文:
 齿轮泵常见故障及排除方法:   故障现象一:泵不能排料:   1、故障原因:a、旋转方向相反;b、吸入或排出阀关闭;c、入口无料或压力过低;d、粘度过高,泵无法咬料.   2、故障排除:a、确认旋转方向;b、确认阀门是否关闭;c、检查阀门和压力表;d、检查液体粘度,以低速运转时按转速比例的流量是否出  现,若有流量,则流入不足。   故障现象二:泵流量不足:   1、故障原因:a、吸入或排出阀关闭;b、入口压力低;c、出口管线堵塞;d、填料箱泄漏;e、转速过低。   2、故障排除:a、确认阀门是否关闭;b、检查阀门是否打开;c、确认排出量是否正常;d、紧固;大量泄露漏影响生产时,应停止运转,拆卸检查;e、检查泵轴实际转速;   故障现象三:声音异常:   1、故障原因:a、联轴节偏心大或润滑不良b、电动机故障;c、减速机异常;d、轴封处安装不良;e、轴变形或磨损。   2、故障排除:a、找正或充填润滑脂;b、检查电动机;c、检查轴承和齿轮;d、检查轴封;e、停车解体检查。   故障现象四:电流过大:   1、故障原因:a、出口压力过高;b、熔体粘度过大;c、轴封装配不良;d、轴或轴承磨损;e、电动机故障。阀门 进口泵 工业洗衣机   2、故障排除:a、检查下游设备及管线;b、检验粘度;c、检查轴封,适当调整;d、停车后检查,用手盘车是否过重;e、检查电动机。   故障现象五:泵突然停止:   1、故障原因:a、停电;b、电机过载保护;c、联轴器损坏;d、出口压力过高,联锁反应;e、泵内咬入异常;f、轴与轴承粘着卡死。   2、故障排除:a、检查电源;b、检查电动机;c、打开安全罩,盘车检查;d、检查仪表联锁系统;e、停车后,正反转盘车确认;f、盘车确认


“ Gear pumps and troubleshooting common faults ”是由提供的水泵行业新闻,译文仅供参考。另外,中国隔膜泵网还提供相关产品搜索:、、、、等。


译文:
Gear pumps and troubleshooting common faults: The phenomenon of a fault: the pump can not nesting: 1, failure reasons: a, rotating in opposite directions; b, suction or discharge valve closed; c, entry no material or pressure too low; d, the viscosity is too high, the pump can not bite material. 2, troubleshooting: a, to confirm the direction of rotation; b, confirm the valve is closed; c, check valves and pressure gauges; d, check the liquid viscosity to the proportion of low-speed running speed of the flow according to whether there is, if flow , is less than inflow. Failure phenomena 2: pump flow less than: 1, failure reasons: a, suction or discharge valve closed; b, low inlet pressure; c, the export pipeline to plug; d, stuffing box leakage; e, speed is too low. 2, troubleshooting: a, confirmed that the valve is closed; b, check whether the valve open; c, to confirm whether the emission of normal; d, fastening; large leak leakage affecting production should cease operation, demolition inspection; e, check the actual speed shaft; Failure phenomenon III: Sound Exception: 1, failure reasons: a, large or poor lubrication eccentric coupling b, motor failure; c, reducer exception; d, seal to install bad; e, axial deformation or wear. 2, troubleshooting: a, to find positive or filling grease; b, check the motor; c, check the bearings and gears; d, check the seal; e, stop the disintegration of inspection. Failure phenomenon IV: overcurrent: 1, failure reasons: a, the outlet pressure is too high; b, melt viscosity is too large; c, seal assembly bad; d, shaft or bearing wear; e, motor failure. Imports of industrial washing machine pump valve 2, troubleshooting: a, check the downstream equipment and piping; b, test viscosity; c, check the seal, appropriate adjustments; d, after stopping checks, hand-drive vehicles are too heavy; e, check the motor. Failure phenomenon V: pump suddenly stops: 1, failure reasons: a, power failure; b, motor overload protection; c, coupling damage; d, outlet pressure is too high, chain reaction; e, pump bite abnormalities; f, shaft and bearing adhesive stuck. 2, troubleshooting: a, check the power supply; b, check the motor; c, open the safety cover, plate vehicle inspection; d, inspection instruments interlock system; e, parking, Reversible drive vehicle to confirm; f, set car identified


原文来源:
<#--{zx1}日志--> <#--推荐日志--> <#--引用记录--> <#--相关日志--> <#--推荐日志--> <#--推荐阅读--> <#--相关文章--> <#--历史上的今天--> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构-->
郑重声明:资讯 【齿轮泵常见故障及排除方法】由 发布,版权归原作者及其所在单位,其原创性以及文中陈述文字和内容未经(企业库qiyeku.com)证实,请读者仅作参考,并请自行核实相关内容。若本文有侵犯到您的版权, 请你提供相关证明及申请并与我们联系(qiyeku # qq.com)或【在线投诉】,我们审核后将会尽快处理。
—— 相关资讯 ——