[Quidway]dis cur                                        ；显示当前配置
[Quidway]display current-configuration                  ；显示当前配置
[Quidway]display interfaces                             ；显示接口信息
[Quidway]display vlan all                               ；显示路由信息
[Quidway]display version                                ；显示版本信息

[Quidway]super password                                       ；修改特权用户密码
[Quidway]sysname                                       ；交换机命名
[Quidway]interface ethernet 0/1                               ；进入接口视图
[Quidway]interface vlan x                               ；进入接口视图
[Quidway-Vlan-interfacex]ip address 10.65.1.1 255.255.0.0     ；配置VLAN的IP地址

[Quidway]ip route-static 0.0.0.0 0.0.0.0 10.65.1.2            ；静态路由＝网关
[Quidway]rip                                                  ；三层交换支持
[Quidway]local-user ftp               增加用户名

[Quidway]user-interface vty 0 4                               ；进入虚拟终端
[S3026-ui-vty0-4]authentication-mode password                 ；设置口令模式
[S3026-ui-vty0-4]set authentication-mode password simple 222 ；设置口令
[S3026-ui-vty0-4]user privilege level 3                       ；用户级别

[Quidway]interface ethernet 0/1                               ；进入端口模式
[Quidway]int e0/1                                             ；进入端口模式
[Quidway-Ethernet0/1]duplex {half|full|auto}                  ；配置端口工作状态
[Quidway-Ethernet0/1]speed {10|100|auto}                  ；配置端口工作速率
[Quidway-Ethernet0/1]flow-control                        ；配置端口流控
[Quidway-Ethernet0/1]mdi {across|auto|normal}                 ；配置端口平接扭接
[Quidway-Ethernet0/1]port link-type {trunk|access|hybrid}     ；设置端口工作模式
[Quidway-Ethernet0/1]port access vlan 3                  ；当前端口加入到VLAN
[Quidway-Ethernet0/2]port trunk permit vlan {ID|All}        ；设trunk允许的VLAN
[Quidway-Ethernet0/3]port trunk pvid vlan 3          ；设置trunk端口的PVID
[Quidway-Ethernet0/1]undo shutdown                       ；xx端口
[Quidway-Ethernet0/1]shutdown                               ；关闭端口
[Quidway-Ethernet0/1]quit                               ；返回

[Quidway]vlan 3                                         ；创建VLAN
[Quidway-vlan3]port ethernet 0/1                 ；在VLAN中增加端口
[Quidway-vlan3]port e0/1                                 ；简写方式
[Quidway-vlan3]port ethernet 0/1 to ethernet 0/4         ；在VLAN中增加端口
[Quidway-vlan3]port e0/1 to e0/4                         ；简写方式

[Quidway]monitor-port <interface_type interface_num>         ；指定镜像端口
[Quidway]port mirror <interface_type interface_num>         ；指定被镜像端口
[Quidway]port mirror int_list observing-port int_type int_num ；指定镜像和被镜像

[Quidway]description string                              ；指定VLAN描述字符
[Quidway]description                                   ；删除VLAN描述字符
[Quidway]display vlan [vlan_id]                               ；查看VLAN设置

[Quidway]stp {enable|disable}                                 ；设置生成树,默认关闭
[Quidway]stp priority 4096                               ；设置交换机的优先级
[Quidway]stp root {primary|secondary}                    ；设置为根或根的备份
[Quidway-Ethernet0/1]stp cost 200                        ；设置交换机端口的花费

[Quidway]link-aggregation e0/1 to e0/4 ingress|both           ; 端口的聚合
[Quidway]undo link-aggregation e0/1|all                       ; 始端口为通道号

[SwitchA-vlanx]isolate-user-vlan enable                  ；设置主vlan
[SwitchA]isolate-user-vlan <x> secondary <list>          ；设置主vlan包括的子vlan
[Quidway-Ethernet0/2]port hybrid pvid vlan <id>          ；设置vlan的pvid
[Quidway-Ethernet0/2]port hybrid pvid                    ；删除vlan的pvid
[Quidway-Ethernet0/2]port hybrid vlan vlan_id_list untagged ；设置无标识的vlan
如果包的vlan id与PVId一致，则去掉vlan信息. 默认PVID=1。
所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged.

原文：