Into the twenty-first century, the people’s living standards improved significantly. To "people-oriented" concept has been widely accepted worldwide as the world’s second-generation composite of chicken essence seasoning monosodium glutamate has been gradually replaced, as it not only delicious, but without any degree of side effects, has become the mainstream of seasoning products.
To the end of 2005, China’s annual consumption of chicken has reached 150,000 tons, and the replacement of relatively MSG is only 20%, so the prospect of a broad market, interested in the development of the industry in the seasoning, of the vast number of capable fighters, experts and scholars. Chicken production line following the matching case for reference, I hope to help all of you. Chicken production process of the preparation indicated raw materials (meat, sugar, salt, etc.) → mixed → Granulator crush → → → drying → packing sifter.
To the end of 2005, China’s annual consumption of chicken has reached 150,000 tons, and the replacement of relatively MSG is only 20%, so the prospect of a broad market, interested in the development of the industry in the seasoning, of the vast number of capable fighters, experts and scholars. Chicken production line following the matching case for reference, I hope to help all of you. Chicken production process of the preparation indicated raw materials (meat, sugar, salt, etc.) → mixed → Granulator crush → → → drying → packing sifter.
Crush the heads of two: First, raw materials of the grinding, the fine powder up to a certain degree of production requirements in line with Essence of Chicken. Second is the finished cake to deal with a second broken.
Salt, sugar, monosodium glutamate, chicken essence of raw materials is the main component of the process according to formula, the proportion of each is different. Usually, the market provided by the above-mentioned raw materials are coarse crystals are larger than 40 mesh, can not be directly engaged in production, you must use the grinder to crush into powder ≤ 80 purpose, to make fine powder and then mixed evenly
Mill is usually used (D) B-type universal grinder, (D) on behalf of the diameter of the tool grinder to crush, such as 20B, 30B, 40B, 60B and so on. The type of grinder is the use of high-speed rotary tool to crush raw materials, and by setting good standards for the collection of products expected to screen. Mill is not any material can be crushed by the moisture content of materials, heat-sensitive, the internal structure of such factors as the impact of the work of the state will have an impact, it was crushed in the choice of materials, it is best to do what the pilot process. As the soft white sugar, grinder, it is easy to plug the screen, so that interruption of work crush. And sugar, monosodium glutamate crystals are more easily crushed. In general, the moisture content below 5%, crystalline, non-heat-sensitive materials crushed effective and efficient. And if a large number of cellulose containing materials (such as Chinese herbal medicine), then the mill should be changed on a number of structures, for certain technical processing, in order to meet production requirements.
B-type pulverizer replacement screen, you can head directly between 5-120 material, so more convenient to use. However, due to more than 80 mesh material is very fine dust easily, it can choose (D) BX-type (ie, dust-type). Against certain manufacturers to produce a large amount of time required to work, can also provide (D) BS-type (that is, water-cooled type). To ensure that the equipment can work long hours, and will not crush the internal heating chamber and the destruction of the quality of materials to be crushed.
In the production process should pay attention to three points: First, will surely opt for stainless steel materials to meet the health requirements; Second, we should always observe the situation of screen to prevent screen damage, so that defective materials increase; three: the end of each work After the screen should be cleaned in time; d: must not have a solid block of material in the debris falls into the crushing chamber.
Salt, sugar, monosodium glutamate, chicken essence of raw materials is the main component of the process according to formula, the proportion of each is different. Usually, the market provided by the above-mentioned raw materials are coarse crystals are larger than 40 mesh, can not be directly engaged in production, you must use the grinder to crush into powder ≤ 80 purpose, to make fine powder and then mixed evenly
Mill is usually used (D) B-type universal grinder, (D) on behalf of the diameter of the tool grinder to crush, such as 20B, 30B, 40B, 60B and so on. The type of grinder is the use of high-speed rotary tool to crush raw materials, and by setting good standards for the collection of products expected to screen. Mill is not any material can be crushed by the moisture content of materials, heat-sensitive, the internal structure of such factors as the impact of the work of the state will have an impact, it was crushed in the choice of materials, it is best to do what the pilot process. As the soft white sugar, grinder, it is easy to plug the screen, so that interruption of work crush. And sugar, monosodium glutamate crystals are more easily crushed. In general, the moisture content below 5%, crystalline, non-heat-sensitive materials crushed effective and efficient. And if a large number of cellulose containing materials (such as Chinese herbal medicine), then the mill should be changed on a number of structures, for certain technical processing, in order to meet production requirements.
B-type pulverizer replacement screen, you can head directly between 5-120 material, so more convenient to use. However, due to more than 80 mesh material is very fine dust easily, it can choose (D) BX-type (ie, dust-type). Against certain manufacturers to produce a large amount of time required to work, can also provide (D) BS-type (that is, water-cooled type). To ensure that the equipment can work long hours, and will not crush the internal heating chamber and the destruction of the quality of materials to be crushed.
In the production process should pay attention to three points: First, will surely opt for stainless steel materials to meet the health requirements; Second, we should always observe the situation of screen to prevent screen damage, so that defective materials increase; three: the end of each work After the screen should be cleaned in time; d: must not have a solid block of material in the debris falls into the crushing chamber.
When the chicken’s raw and auxiliary materials are state of the powder is ready, the Essence of the production process technology will enter the second paragraph – mixed.
The purpose of mixing is the ratio of the raw materials for a wide range of uniform distribution to ensure that each batch to maintain consistency of product quality. Chicken production process can be divided into the mixed before pelleting mixed (mixed raw materials for the granulation to prepare) and finished mixed after the (finished product attached to particles in the mixture in some essence or oily substances).
According to the method of mixing, the wet mixture can be divided into dry mixture. Essence of Chicken are as a result of wet granulation, it can not be separated from the wet mix. The equipment must be wet mixed with stirring devices mandatory in order to facilitate the mixed materials. There are usually two such equipment: twin-screw conical mixer and the mixer channel CH. Although the twin-screw conical mixer mixing power, but because of its corners, and clean and seldom used inconvenience. The mixer has a large number of CH trough advantages: large openings, no dead ends, cleaning convenient, easy to operate. These advantages have become the essence CH mixer trough of essential production equipment products.
Mixer trough-shaped due to the manger outside the image name. There are two most common: Tung Lo-axis and dual-band type. Most of the work of the same principle: put in a mixed cavity For a mixture of materials, usually containing a factor of 0.4, the first dry-mixed a few minutes, and then Add eggs, water, oily substances, such as raw materials, through the spiral of non-stop with orFlip and stir to fully mixed materials. Trough mixer is the quality control point of the shaft seal cavity with mixture. Sealed properly, will be tiny particles into the gap and bearings, two, three weeks mixer will not work correctly. At the same time, after each frequency is also very important to clean equipment.
Also referred to the previous dry-mixed, dry mixed using materials from the mixed impact of gravity method. Wet mix to dry mix before a certain advantage: the ratio of raw materials could be some great difference between the mixed raw materials (tens of kilograms to tens of grams), so as to ensure the best quality. Dry mixing equipment usually have: V-type mixer, SYH-type three-dimensional motion mixer, high-speed mixing granulating machine.
No matter what type of mixer, in the choice should pay attention to the following questions:
1. Materials will surely opt for stainless steel and polished inside and outside the do-wide.
2. Equipment must be no dead ends, welding Department to fine grinding in order to avoid welding slag into the food.
3. Equipment is set to be running, listening to his voice, to check equipment and bearings coaxiality quality. Add water to test the sealing operation.
The purpose of mixing is the ratio of the raw materials for a wide range of uniform distribution to ensure that each batch to maintain consistency of product quality. Chicken production process can be divided into the mixed before pelleting mixed (mixed raw materials for the granulation to prepare) and finished mixed after the (finished product attached to particles in the mixture in some essence or oily substances).
According to the method of mixing, the wet mixture can be divided into dry mixture. Essence of Chicken are as a result of wet granulation, it can not be separated from the wet mix. The equipment must be wet mixed with stirring devices mandatory in order to facilitate the mixed materials. There are usually two such equipment: twin-screw conical mixer and the mixer channel CH. Although the twin-screw conical mixer mixing power, but because of its corners, and clean and seldom used inconvenience. The mixer has a large number of CH trough advantages: large openings, no dead ends, cleaning convenient, easy to operate. These advantages have become the essence CH mixer trough of essential production equipment products.
Mixer trough-shaped due to the manger outside the image name. There are two most common: Tung Lo-axis and dual-band type. Most of the work of the same principle: put in a mixed cavity For a mixture of materials, usually containing a factor of 0.4, the first dry-mixed a few minutes, and then Add eggs, water, oily substances, such as raw materials, through the spiral of non-stop with orFlip and stir to fully mixed materials. Trough mixer is the quality control point of the shaft seal cavity with mixture. Sealed properly, will be tiny particles into the gap and bearings, two, three weeks mixer will not work correctly. At the same time, after each frequency is also very important to clean equipment.
Also referred to the previous dry-mixed, dry mixed using materials from the mixed impact of gravity method. Wet mix to dry mix before a certain advantage: the ratio of raw materials could be some great difference between the mixed raw materials (tens of kilograms to tens of grams), so as to ensure the best quality. Dry mixing equipment usually have: V-type mixer, SYH-type three-dimensional motion mixer, high-speed mixing granulating machine.
No matter what type of mixer, in the choice should pay attention to the following questions:
1. Materials will surely opt for stainless steel and polished inside and outside the do-wide.
2. Equipment must be no dead ends, welding Department to fine grinding in order to avoid welding slag into the food.
3. Equipment is set to be running, listening to his voice, to check equipment and bearings coaxiality quality. Add water to test the sealing operation.
