PPPoE配置(二)_yanyu203020的空间_百度空间

【简 介】
很多公司使用ADSL宽带线路作为备份线路,同时作为内部上网的分流线路。这有两种配置:一种是cisco路由器连接ethernet接口连接ADSL的modem;一种是在cisco路由器上安装ADSL WIC卡,直接连接ADSL电话线。

说明:

  很多公司使用ADSL宽带线路作为备份线路,同时作为内部上网的分流线路。这有两种配置:一种是cisco连接ethernet接口连接ADSL的modem;一种是在cisco路由器上安装ADSL WIC卡,直接连接ADSL电话线。

  Cisco路由器连接ADSL modem的PPPoE配置:........................................................ 1

  Cisco路由器连接ADSL WIC卡之PPPoE配置:........................................................ 3

  Cisco路由器连接ADSL modem的PPPoE配置:

  hostname bjsite

  !

  ip subnet-zero

  no ip domain-lookup

  !

  vpdn enable

  no vpdn logging

  !

  vpdn-group 1

  request-dialin

  protocol pppoe

  !

  interface Ethernet0/0

  ip address 192.168.0.1 255.255.255.0

  ip nat inside

  no ip mroute-cache

  !

  !

  !

  !

  interface Ethernet0/1

  no ip address

  pppoe enable

  pppoe-client dial-pool-number 1

  !

  interface Dialer1

  ip address negotiated

  ip nat outside

  ip mtu 1492

  encapsulation ppp

  no ip mroute-cache

  dialer pool 1

  dialer-group 1

  ppp authentication pap

  ppp pap sent-username dg48907653@163.gd password xxxxxxxx

!

  ip classless

  no ip http server

  !

  dialer-list 1 protocol ip permit

  ip nat inside source list 1 interface Dialer1 overload

  ip route 0.0.0.0 0.0.0.0 dialer1

  access-list 1 permit 192.168.0.0 0.0.0.255

  !

  line con 0

  exec-timeout 0 0

  transport input none

  line vty 0 4

  login

  !

  end

  Cisco连接ADSL WIC卡之PPPoE配置:

  vpdn-group pppoe

  request-dialin

  !--- we are the PPPoE client requesting to establish

  !--- a session with the aggregation unit (6400 NRP).

  protocol pppoe

  !

  !--- internal Ethernet network.

  !

  interface FastEthernet0

  ip address 10.92.1.182 255.255.255.0

  ip nat inside

  !--- DSL interface.

  !

  interface ATM0

  no ip address

  no atm ilmi-keepalive

  bundle-enable

  dsl operating-mode auto

  hold-queue 224 in

  !--- All defaults.

  !--- PPPoE runs on top of AAL5SNAP, but the

  !--- encap aal5snap command is not used.

  !

  interface ATM0.1 point-to-point

  pvc 1/1

  pppoe-client dial-pool-number 1

  !--- pvc 1/1 is an example value that must be changed

  !--- to match the value used by the ISP.

  !

  !--- The PPPoE client code ties into a dialer interface upon

  !--- which a virtual-access interface is cloned.

!

  interface Dialer1

  ip address negotiated

  ip mtu 1492

  !--- Ethernet MTU default = 1500 (1492 + PPPoE headers = 1500)

  ip nat outside

  encapsulation ppp

  dialer pool 1

  !--- Ties to atm interface.

  ppp authentication chap callin

  ppp chap hostname

  ppp chap password

  !

  !--- The ISP will instruct you regarding

  !--- the type of authentication to use.

  !--- To change from PPP CHAP to PPP PAP,

  !--- replace the following three lines:

  !--- ppp authentication chap callin

  !--- ppp chap hostname

  !--- ppp chap password

  !--- with the following two lines:

  !--- ppp authentication pap callin

  !--- ppp pap sent-username password

  !--- For NAT we are going to overload on the Dialer1

  !--- interface and add a default route out

  !--- since dialer ip address can change.

  ip nat inside source list 1 interface Dialer1 overload

  ip classless

  ip route 0.0.0.0 0.0.0.0 dialer1

  no ip http server

  !

  access-list 1 permit 10.92.1.0 0.0.0.255



郑重声明:资讯 【PPPoE配置(二)_yanyu203020的空间_百度空间】由 发布,版权归原作者及其所在单位,其原创性以及文中陈述文字和内容未经(企业库qiyeku.com)证实,请读者仅作参考,并请自行核实相关内容。若本文有侵犯到您的版权, 请你提供相关证明及申请并与我们联系(qiyeku # qq.com)或【在线投诉】,我们审核后将会尽快处理。
—— 相关资讯 ——