模具钢材
alloy tool steel 合金工具钢 aluminium alloy 铝合金钢 bearing alloy 轴承合金 blister steel 浸碳钢 bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢
marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel
钼系高速钢 molybdenum steel
钼钢 nickel chromium steel 镍铬钢
prehardened steel 顶硬钢
silicon steel sheet 硅钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
四、模具零件: mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝: screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold base
上内模:cavity insert
下内模:core insert
行位(滑块): slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
xx柱:spring rod
xx:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子xx:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件: Do not use (core/cavity) insert
用铍铜做镶件: use beryllium copper insert
初步(正式)模图设计:preliinary (final) mold design
反呵:reverse core
xx压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
,他说:想发财就去找优质供货商!;均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode
模具工程常用词汇
die 模具 die shoe 模瓦
figure file, chart file图档
cutting die, blanking die冲模
progressive die, follow (-on)die 连续模
compound die复合模
punched hole冲孔 panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
design modification设计变化 die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧 bolt螺栓
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
incoming material to be inspected进货待验
PCE assembly production schedule sheet PCE组装厂生产排配表
model机锺
work order工令
revision版次
production control confirmation生产确认
checked by初审
approved by核准
stock age analysis sheet 库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked 待验或重工
cause description原因说明
part number/ P/N 料号
item/group/class类别
prepared by制
year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品
on way location在途仓
oversea location海外仓spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割 EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔+